# POPstar general config
# Lines beginning # are comments

# SMTP server
# This can be a system variables surrounded by <>'s, eg <SMTP$Server>
SMTP:mail.isp.net
# If you need to authenticate to your SMTP server, comment the next two
# lines and fill in your username/password.
# These make also be set to a system variable in the same way as 'SMTP:'
#SMTP.username:myusername
#SMTP.password:mypassword

# Frequency of automatic fetches and sends (minutes)
FetchEvery:4
SendEvery:1

# Only do automatic transfers if following variable is defined
# Omit or comment if no suitable variable
# Variable:PPP$Connected

# Set to Y to make sends take priority over fetches
SendFirst:N

# Automatically open status window when transferring:
# 0: never
# 1: only when there's something to download
# 2: immediately
# 3: the first time, and also when there's something to download
AutoStatus:2

# Full size status window (Y/N)
BigStatus:Y

# Automatic fetch when loaded (Y/N)
AutoFetch:N

# Automatic send when loaded (Y/N)
AutoSend:N

# Automatic quit when transfers complete
AutoQuit:N

# Find size of messages before fetching (Y/N)
List:Y

# Length of line terminators (usually 2 for CR-LF)
# Used only when estimating progress through a message
LineTermLen:2

# Show icon bar icon
IconBar:Y

# Maximum CPU time used between Wimp polls while transferring (cs)
Nice:20

# If 'Y', send outgoing messages even if online variable indicates we're
# offline (useful if you have a dialup connection, but a permanent
# SMTP server on a local net)
SendOffline:N

# Maximum size message to download, in bytes (or suffix with K or M)
# may be over-ridden on a per-user basis in the users file
# 0 means unlimited
# NB. If this is anything other than unlimited, 'List' will be enabled
# automatically
# Examples : 0, 100K, 1M [do not put a space between the number and the K/M]
MaxSize:0

# Numbers of lines of message body to fetch when we find a message that
# exceeds the configured 'MaxSize:'.
OversizeMsgLines:10

# Numbers of seconds to wait when asking the user what action to take with an
# oversize message.
# Once the timeout expires, the message header will be downloaded and the
# message will be left on the server.
# Setting to 0 will disable the oversize query window
# NB. Don't set this to a huge value - if we stop for too long, we risk the
# POP3 server deciding we're idle and kicking us off.
OversizeQueryWait:20

# Whether to beep when an oversize message dialogue box is shown.
# Default: N
OversizeBell:N

# Maximum number of queued commands to send.
# Top limit is 15. Increasing from 0 will improve speed, especially over
# slow links
MaxPipeSize:0

# Whether or not to quit when POPstar notices an on -> off-line transition
# Default: N
QuitWhenGoOffline:N

# How often to check the variable specified in Variable: (in seconds)
# Default: 10 seconds
CheckOnlineVar:10

# Whether or not to send the QUIT command to the POP3 server before closing
# the connection when an error occurs.
# Don't change this unless you need to (eg. If your ISP auto deletes mail
# after is has been retrieved. 99% of them don't, ndirect.co.uk do.)
# Default: Y
SendQuitOnError:Y

# This limits the number of messages fetched in one connection to the POP3
# server.
# If the limit is exceeded, POPstar will reestablish the connection to the
# server before downloading more messages - this stops you having to
# download all the messages again if the connection to the POP3 server
# is lost for some reason.
#
# Default: fetch all messages in one connection
MaxMessagesPerConnection:40

# This limits the maximum size of messages fetched in one connection to
# the POP3 server.
# If the limit is exceeded, POPstar will reestablish the connection to the
# server before downloading more messages - this stops you having to
# download all the messages again if the connection to the POP3 server
# is lost for some reason.
#
# Default: fetch all messages in one connection
MaxSizePerConnection:100K

# This is a command that will be run at the end of every transfer POPstar
# makes.
# Default: nothing
# TransferEnd: <POPstar$Dir>.!TransferEnd

# This is a command that will be run after every fetch, with the first
# parameter containing the number of messages fetched.
# Default: nothing
# FetchEnd: <POPstar$Dir>.!FetchEnd

# This is a command that will be run after every send, with the first
# parameter containing the number of messages sent.
# Default: nothing
# SendEnd: <POPstar$Dir>.!SendEnd


# If this is set to N, POPstar won't report errors that occurs whilst trying
# to establish a connection to the POP3 server.
# Default: Y
ReportConnectFailure:Y

# Time, in seconds, that server can take to reply before we decide the
# operation has timed out.
# Default: 300 (5 minutes)
SocketTimeout:300
